Pick golf shank drills by cause. A shank often has one of three causes, and each one calls for a different drill.
What Causes You to Shank the Golf Ball
A shank happens when the ball hits the hosel, the part of the club where the shaft meets the clubhead, instead of the clubface. You can shank any iron, and a few in a row can ruin a round. Everyone in the bay will offer a diagnosis afterward, and most of them will be wrong.
If you keep shanking your irons, the problem often traces back to one of three causes. First, an out-to-in swing sends the club across the ball from outside the target line. Second, an in-to-out swing drops the club too far behind you and then flings it out at the ball. Third, a weight shift: your body lunges toward the ball on the downswing.
In all three, either the clubhead or your body ends up closer to the ball than it should be at impact, so the hosel gets there before the clubface. The right drill fixes that position. Standing too close to the ball or too far from it can change where your club and weight end up, so Step 1 starts there.
Step 1: Fix Your Setup Before You Swing
To avoid shanking the golf ball, check two things before the club moves: how far you stand from the ball and where your weight sits.
Stand where your arms hang freely. Crowd the ball and your arms have no room, so they push away from you to make space. Reach for it and your weight tips onto your toes.
Set your weight in the middle of your feet. Weight on the toes and over the ball is a common setup for a shank.
Then test your setup. If you suspect you crowd the ball, try CaddieHQ’s check: right before the backswing, take a half step back from the ball, away from the target line, then swing normally. That small reach is deliberate: CaddieHQ says it pushes contact toward the middle of the face and away from the heel. The reach to avoid is the big one that tips your weight onto your toes. After that, hit a few slow half swings and stay centered, with no dive toward the ball. If the setup still feels new, start with these golf swing drills for beginners.
Step 2: Find Out Which Kind of Shank You Hit
Your cause decides which drill to run, so find it first. These directions are for right-handed golfers, so mirror them if you swing left handed.
Of the two swing paths, out-to-in (coming over the top) is the more common cause, and in-to-out is the one better players tend to hit.
A simple test needs no screen: set a soft headcover just outside the ball (read the safety note in Step 3 first). If your club hits it before the ball, you are coming over the top. If it clips the marker after the ball, you are swinging in-to-out. On an X-Golf Frisco bay, the screen also shows your Club Path in degrees after every swing, which is the direction your clubhead travels through impact. Under the standard Club Path convention, a positive number means in-to-out and a negative one means out-to-in, so a handful of swings that mostly lean one way show your pattern. Watch whether that number moves toward zero as you run the marker drill.
The screen does not measure your body, so the lunge is the cause you feel instead of read: your weight ends up on your toes and over the ball. Match your cause to a drill below.
Which cause gets which drill:
| Your Cause | What the Hosel Is Doing | Drill to Start With |
| Out-to-in swing | The club crosses the ball from outside, so the ball meets the hosel | Marker drill: miss it before the ball |
| In-to-out swing | The club drops behind you, then swings out, so the ball meets the hosel | Marker drill: miss it after the ball |
| Lunge toward the ball | Your lunge pushes the hands and clubhead outward, which exposes the hosel | Feet-together drill |
| Not sure which | The heel is meeting the ball | Four-tee drill, as a check |
Step 3: Run the Shank Drill That Fits Your Miss
Pick the drill that matches your cause from Step 2 and run it slowly before you go back to full swings. That is how to fix a shank in golf.
Use one drill at a time. The marker drill uses something soft, such as a headcover or a rolled towel. Stop if you lose your balance, and ask a staff member before you set a marker down in the bay. A shank can also fly off at a sharp angle, so keep everyone in the bay out of the ball’s way as well as the club’s.
Marker Drill for Path Shanks
A marker just outside the ball tells you right away when your swing path is off.
Set a headcover just outside the ball, with the toe of your club almost touching it at address, and grab a wedge. Take slow half swings. The way you hit the marker tells you what to fix:
- Out-to-in: if you come over the top, the club hits the marker before it reaches the ball. To miss it, bring the club down from the inside.
- In-to-out: if your club flings out to the right too much, it clips the marker after the ball. To miss it, swing through square and let the club return around your body instead of flinging out.
Keep going until you can miss the marker on 20 shots in a row, which is Golf Monthly’s target for this drill. Then build up gradually to a three-quarter swing, and stop if you hit the marker. On a bay, compare your Club Path over the first few swings with the last few, and look for the number to move toward zero.
Feet-Together Drill for Weight on Toes
A feet together stance leaves no room to lunge toward the ball.
Take a short iron, such as a 9-iron, and set your feet so they touch or sit about an inch apart. Hit short, easy shots of about 50 to 70 yards, and stop if you feel yourself tipping forward.
With a narrow stance, the only way to stay balanced is to rotate around your spine. If you lunge, sway or fall forward, you lose your balance right away. Lunge is what pushes your hands and clubhead outward and exposes the hosel. Pete Cowen, Henrik Stenson’s longtime coach, teaches a feet-together drill for full swings too, because it encourages you to keep your knee and chin levels constant. Once the shots feel steady, widen your stance back to normal and keep the same centered feel.
Four-Tee Drill for Clean Contact
Four tees give you a wall to stay away from.
LPGA teacher Cathy Kim sets four tees down side by side like a small wall and grounds a 7-iron on the front side of them, with the ball in the middle of the clubface. The goal is to avoid striking the ball with the heel, and the tees show you where the heel is going. Swing without touching the tees. Ask a staff member whether your bay surface takes tees, and keep the swing slow.
Reset Fast When a Shank Shows Up
After one shank, slow down and hit short chips before you swing full again.
Keep the reset short:
- Slow down. Our guide to finding your golf swing tempo shows how to find a pace you can repeat.
- Hit 10 or 15 short chips. Each one should strike the ball first and send it off the middle of the face.
- Go back to your full swing and see whether the contact feels better.
A shorter, chip-style swing can show you what changed in your contact, and it can sometimes settle a shank on its own. If the club starts hitting the turf first instead, read how to stop chunking your irons.
Take Your Shank Fix to X-Golf Frisco
Before you book, pick your drill and run it slowly. In a bay, the Club Path number shows whether your path is changing.
A Frisco bay lets you repeat that drill with no weather dependency. Book a bay at X-Golf Frisco, and bring a friend to watch from the seating area, well clear of your swing. Food and drinks come to your bay, so settle in.
If the shank keeps coming back, book golf lessons at X-Golf Frisco with PGA Professional Jason Cole, who has taught more than 46,000 lessons. Lessons at X-Golf Frisco use simulator data and video to show you what your swing is doing.